American-lighting AL-WF-WH Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Beleuchtung American-lighting AL-WF-WH herunter. American Lighting AL-WF-WH User Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 2
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
©2012 American Lighting
Denver, CO 80231 Made in China
READ ALL OF THESE INSTALLATION INSTRUCTIONS BEFORE INSTALLING THE FIXTURE. FAILURE TO
FOLLOW INSTALLATION INSTRUCTIONS AND ALL APPLICABLE ELECTRICAL CODES WILL VOID THE
PRODUCT WARRANTY.
WARNING:
These products may represent a possible shock or fire hazard if improperly installed or attached in any
way. Products should be installed in accordance with these instructions, current electrical codes and/or
the current National Electric Code (NEC).
WARNING:
Disconnect supply power from the source prior to installation. This product must be installed by a
person familiar with the construction and operation of the product and the hazards involved, and in
accordance with current electrical codes and/or the current National Electric Code (NEC). Consult a
local licensed electrician if you are not sure about the installation. To reduce potential of electric shock,
fixture must be grounded.
APPLICATION / USE:
This product is rated for use in wet locations and designed for surface mounting only. Best practices include
mounting fixture to a standard 4” octagonal electrical box. If an existing electrical box is an odd size, you may
need to purchase an additional canopy from an electrical supplier or home supply center. Check size carefully
before attempting to mount fixture.
INSTALLATION:
Disconnect supply power from the source prior to installation.
1. Feed the black, white and copper wires through the 1/2“ opening of the canopy, thread the fixture’s
mounting arm into the opening and secure it with the 1/2” locknut.
2. If applicable, install photocell and/or motion sensor (not
included) using additional 1/2” NPS opening (remove cap
and install sensor using manufacturers instructions).
3. Remove old fixture if applicable.
4. Connect line voltage (hot) AC supply wire(s) (Black) to the
line voltage AC wire(s) (Black) inside the canopy via
the attached quick electrical stab connector.
5. Connect neutral (common) AC supply wire(s) (White) to the
neutral AC wire(s) (White) inside the canopy via
the attached quick electrical stab connector.
6. Connect the ground AC supply wire(s) [Green or bare wire(s)]
to the ground AC wire(s) [bare copper wire(s)] using an
appropriate UL Listed electrical connector.
7. Cap and insulate all unused leads.
8. To aim the light, loosen the side bolt connected to the arm
knuckle to aim the fixture up or down. Re-tighten bolt to secure the fixture in the desired position.
9. For a rain-tight seal, caulk the top and sides of the canopy and the aiming arm joint, with silicone caulking
compound. See Figure 1.
ADDITIONAL SAFETY MEASURES:
1. LEDs are not serviceable. Do not attempt to open the LED light engine.
2. LEDs are bright. Do not look directly into fixture.
3. Not intended for recess mounting in any type of installation.
www.americanlighting.com
LED PANORAMA FLOOD LIGHT
Installation instructions for AL-WF-DB and AL-WF-WH
Figure 1
For a rain-tight seal, caulk the top and sides
of the canopy and the aiming arm joint(s).
Canopy
Aiming arm
joint
RV-1233
Additional 1/2” NPS opening
Seitenansicht 0
1 2

Inhaltsverzeichnis

Seite 1 - LED PANORAMA FLOOD LIGHT

©2012 American LightingDenver, CO 80231 Made in ChinaREAD ALL OF THESE INSTALLATION INSTRUCTIONS BEFORE INSTALLING THE FIXTURE. FAILURE TO FOLLOW INST

Seite 2 - LED PANORAMA EXTENSION ARMS

©2013 American LightingDenver, CO 80231 Made in ChinaREAD ALL OF THESE INSTALLATION INSTRUCTIONS BEFORE INSTALLING THESE ACCESSORIES. FAILURE TO FOLLO

Verwandte Modelle: AL-WF-DB

Kommentare zu diesen Handbüchern

Keine Kommentare